The requirements
1.1 This approved document, which takes effect on 6 April 2014, deals with the energy efficiency requirements in the Building Regulations 2010. Regulation 2(1) of the Building Regulations defines the energy efficiency requirements as the requirements of regulations 23, 25A, 25B, 26, 26A, 28, 29 and 40 and Part L of Schedule 1. The energy efficiency requirements relevant to the guidance in this approved document, which deals with new buildings, are those in regulations 25A, 26, 29 and 40 and Part L of Schedule 1, and are set out below.
NOTE: Regulation 25B 'Nearly zero-energy requirements for new buildings' will not come into force until 2019 at the earliest. Statutory guidance on compliance with regulation 25B is not included within this approved document and will be provided nearer to the time that regulation 25B comes into force.
1.2 Relevant extracts from the Building Regulations 2010 or the Building (Approved Inspectors etc.) Regulations 2010 (both as amended) are set out using text against a green background in this approved document. Where there is any doubt you should consult the full text of the regulations, available at http://www.legislation.gov.uk
Requirement
Schedule 1 – Part L Conservation of fuel and power
L1. Reasonable provision shall be made for the conservation of fuel and power in buildings by:
(a) limiting heat gains and losses–
(i) through thermal elements and other parts of the building fabric; and
(ii) from pipes, ducts and vessels used for space heating, space cooling and hot water services;
(b) providing fixed building services which–
(i) are energy efficient;
(ii) have effective controls; and
(iii) are commissioned by testing and adjusting as necessary to ensure they use no more fuel and power than is reasonable in the circumstances.
Demonstrating compliance
1.3 In the Secretary of State's view, compliance with the energy efficiency refquirements could be demonstrated by meeting the five separate criteria set out in the following paragraphs. Compliance software should produce an output report to assist BCBs check that compliance has been achieved.
NOTE: The output report can benefit both developers and BCBs during the design and construction stages as well as at completion.
1.4 Criterion 1: in accordance with regulation 26, the calculated CO2 emission rate for the building (the Building CO2 Emission Rate, BER) must not be greater than the Target CO2 Emission Rate (TER), which is determined by following the procedures set out in paragraphs 2.7 to 2.36.
NOTE: Criterion 1 is a regulation and is therefore mandatory, whereas the limits on design flexibility for Criteria 2 are statutory guidance. The calculations required as part of the procedure used to show compliance with this criterion can also provide information needed to prepare the energy performance certificate required by regulation 29 of the Building Regulations and by the Energy Performance of Buildings (England and Wales) Regulations 2012 (SI 2012/3118).
1.5 Criterion 2: the performance of the individual fabric elements and the fixed building services of the building should achieve reasonable overall standards of energy efficiency, following the procedure set out in paragraphs 2.37 to 2.49.
NOTE: Criterion 2 is intended to place limits on design flexibility to discourage excessive and inappropriate trade-offs. For example, individual building fabric elements with poor insulation standards being offset by renewable energy systems with uncertain service lives. This emphasises the purpose of Criterion 2.
1.6 Criterion 3: demonstrate that the building has appropriate passive control measures to limit solar gains. The guidance given in paragraphs 2.50 to 2.53 of this approved document provides a way of demonstrating that suitable provisions have been made.
NOTE: The purpose is to limit solar gains to reasonable levels during the summer period, in order to reduce the need for, or the installed capacity of, air-conditioning systems.
1.7 Criterion 4: the performance of the building, as built, should be consistent with the BER. The guidance in Section 3 can be used to show that this criterion has been met. Extra credits will be given in the TER/BER calculation where builders can provide robust evidence of quality-assured procedures in the design and construction phases.
1.8 Criterion 5: the necessary provisions for enabling energy-efficient operation of the building should be put in place. The procedures described in Section 4 can be used to show that this criterion has been met.
